Skip to content

VR-TABLE PRO Dual-Side ISP/ICSP SD/MMC SPI UART JTAG

Scroll to explore
Non-invasive ISP/ICSP reading and writing redefined.

Features of VR‑TABLE PRO

A workstation for solderless contact with PCB test points - controlled, repeatable, and safe.

Work on both sides of the PCB without remounting - the board stays fixed and aligned.
Dual‑Side
Work with eMMC/UFS in automotive modules and mobile devices without soldering.
SD/MMC / MPH-Y
Board-level diagnostics and serial communication with CPU, SoC and MCU.
UART + JTAG
Device communication and service modes for smartphones.
USB / FBUS
NOR / SerialNAND memory access for IoT devices, GPS units and embedded electronics.
SPI

Solderless workflow

No direct soldering to test points leaving traces of interference.

Reduces the risk of permanent PCB damage and saves time during setup.

Stable contact

Consistent probe pressure and positioning during extended operations.

Minimizes the risk of connection loss or interrupted communication.

Cleaner platform (I/O)

Integrated holders, arms, probes and adapter support.

Less cable clutter and improvised wiring on the bench.
Dual-side

Work both sides of the PCB without remounting.

Many modern PCBs require access to points on both the top and bottom of the board. VR-TABLE PRO gives controlled access to both sides.

No unnecessary remounting
The board stays in position while you work from both sides.
Better control on complex jobs
Power, data, clock and reset points across different PCB layers.
Comfortable microscope work
The board remains fixed while you focus on probe placement.
Work both sides of the PCB without remounting.

How it works

From board to data in four steps

  1. 1

    Mount & align the board

    Secure the PCB in the dual-side fixture and set a stable, repeatable position.

  2. 2

    Locate test points

    Bring the micrometric arms to the test points and lock in clean, steady contact.

  3. 3

    SD/MMC SPI UART JTAG

    Prepare the right service box to connect to VR-TABLE PRO.

  4. 4

    Connect your box & work

    Insert a slide-in adapter and hook up Z3X / Easy-JTAG, Medusa Pro, UFI Box, FLASH64, or Octoplus.

Who it’s for

Built around real professional workflows

Forensic laboratories

Non-invasive acquisition workflows where repeatability and controlled handling matter.

Data recovery laboratories

ISP/ICSP workflows over SD/MMC/MPH-Y and SPI, as well as UART and JTAG-based board-level access on devices requiring reliable contact.

Mobile service and repair centers

Advanced diagnostics, board-level access and communication with supported devices without direct soldering.

Police, government and investigation units

Professional workstation for repeatable technical operations on mobile and embedded electronics.

Automotive electronics specialists

Work with car radios, modules, controllers and communication interfaces where stable probing is required.

Dedicated adapters

Connect your service box in a simple way

VR-TABLE PRO slide-in adapter

Slide-in adapters

Slide-in adapters connect the workstation with popular service boxes and programmers - the technician inserts the required adapter instead of rebuilding the connection each time, keeping the setup organized with a cleaner signal path.

  1. 1
    Slide into the holder

    Drop the adapter into the arm - no tools needed.

  2. 2
    Connect the cables

    Attach the power and signal leads to the adapter.

  3. 3
    Connect your box

    Hook up Z3X or another programmer and start working.

Service box holder

Dedicated service box holder uses the securing screw of the height extenders, creating a stable place for devices such as Medusa PRO II and FLASH64.

VR-TABLE PRO service box holder mounted to a height extender
Works with popular service boxes
Z3X / Easy-JTAG
Medusa Pro
UFI Box
FLASH64
Octoplus

All trademarks are the property of their respective owners. Compatibility information is provided for reference only and may depend on the selected adapter, external tool, target device and workflow configuration.

Power module

Touchscreen-controlled power management

A dedicated VR-TABLE PRO power module with touchscreen-controlled power management for professional ISP/ICSP workflows - built for memory interfaces and board-level access scenarios.

  • Touchscreen control of selected power lines
  • Fixed 3.3 V, 2.8 V and 1.8 V outputs
  • Adjustable VCCQ line from 1.2 V to 3.6 V
  • Live current monitoring during operation
Power Supply Module
Power
3.3V220mA
2.8V187mA
1.8V120mA
1.2V080mA
Voltage
1.2 V

Why VR-TABLE PRO

Less risk than traditional rework

Traditional rework
  • Desolder the chip and expose it to heat
  • Slow, one-off, hard to reproduce
  • Needs a dedicated soldering station (BGA, hot-air)
  • Risk of lifted pads and board damage
VR-TABLE PRO
  • Board stays intact - no desoldering
  • Fast setup you can repeat any time
  • Bench-ready - first read in minutes
  • Controlled, low-risk contact
  1. /01VR-TABLE PRO main unit
  2. /0210 modular micrometric arms
  3. /03Spring-loaded 3 in 1 probes
  4. /04Slide-in adapters and power supply module
  5. /05Power and signal cables (30 cm)
  6. /06Transport case

Equip your workspace with VR-TABLE PRO